Vmc Machine, 3 4 Axis Vmc Machine, Vmc Center, Vmc Machining, Vmc Machining Center Vmc5025

 Structural performance of machine tool1. Fuselage designThe fuselage and saddle are reinforced by mountain shaped ribs, with the shortest force streamline, ensuring the best rigidity of the fuselage.Based on the excellent engineering design, the stiffeners of the base and column of the machining center can resist the torsi

Featured Products

Vmc Machine, 3 4 Axis Vmc Machine, Vmc Center, Vmc Machining, Vmc Machining Center Vmc5025

Vmc Machine, 3 4 Axis Vmc Machine, Vmc Center, Vmc Machining, Vmc Machining Center Vmc5025 Structural performance of machine tool
1. Fuselage design
The fuselage and saddle are reinforced by mountain shaped ribs, with the shortest force streamline, ensuring the best rigidity of the fuselage.
Based on the excellent engineering design, the stiffeners of the base and column of the machining center can resist the torsion and damping, and transfer the cutting vibration to non
Cutting area. The column is designed with torque tube, which can provide excellent rigidity, bending and torsion resistance Ultra wide base design,
At the same time, lower the center of gravity of the base and adjust the center of gravity of the machine tool to the best stable height. The span at the bottom of the column is widened to improve the stability of the machine tool.
2. spindle head
The contact length ratio between the main shaft and the column is appropriate to provide stable support for the main shaft. Independent cooling system is built in the spindle head to stabilize the spindle continuously
The head heat is in a reasonable range, which reduces the thermal extension of the spindle and ensures the machining accuracy.

3. counterweight
In response to the processing requirements of different models, the following counterweight methods are adopted:
Counterweight: low failure rate and long service life;
Nitrogen counterweight: rapid action, no noise, greatly improved processing accuracy, increased machine life;
No counterweight: in order to meet the requirements of high speed and high sensitivity processing, the machine tool adopts the method of no counterweight, and enhances the requirements of servo motor and screw,
Z-axis with brake, to ensure the accuracy of the machine tool is stable and lasting, and increase the service life.
4. screw rod
It adopts imported grinding level pre drawn double nut screw rod to eliminate reverse clearance. After heat treatment, it has high rigidity, wear resistance, torsion resistance and long service life, which guarantees high machining accuracy of the machine.
5. AC servo motor
Adopt original imported from Japan, super high performance servo motor, provide stronger power when heavy cutting.
In the case of low feed, high torque can still be maintained.
Higher than 10000 (pixel) resolution and closed-loop position feedback ensure high accuracy.
High quality coupling ensures that the screw rod moves with the axis of the motor.
6. Lubrication system
The whole machine adopts a positive displacement lubrication system and a de pressurized oil pump, with stable pressure and flow, which effectively transports the oil to each lubrication point and provides uniform forced lubrication for each slide surface, so as to ensure the accuracy and service life of the machine tool.
7.
Chip remover system


Vmc Machine, 3 4 Axis Vmc Machine, Vmc Center, Vmc Machining, Vmc Machining Center Vmc5025
ItemunitTAT-5025
operating range
X-axis travel (left and right)  mm5000
Y-axis travel (front and rear)  mm2500
Z-axis travel (up and down)   mm1000
Distance from worktable to spindle end face
mm
260-1260
Distance from the front end of column to the center of main shaft

mm

600
Workbench
Table area (L * W)mm2300*5000
maximum loadkg6500
T-groove (width * spacing * number of grooves)
mm
11*28*200
X / Y / Z axis rapid feedm/min10m/min
Spindle specification
Spindle speedrpm4000/6000
Taper hole form and installation size
kg

BT40∮140(external diameter)
Transmission mode (1:1)mmBelt
Recommended motor parameters for spindle
kW

25
Accuracy (x / Y / z)
positioning accuracymm±0.003/300
Repeated positioning accuracymm±0.003/300
Other information
Three axis powerkw7*4.5*4.5
system FANUC OI-MF
Tool magazineT60
Machine size floor space                              
(L * w*h)

mm

2700*2400*2500
Pressure sourcekg/cm²10
Power capacityKva20
machine weight kg53000
Vmc Machine, 3 4 Axis Vmc Machine, Vmc Center, Vmc Machining, Vmc Machining Center Vmc5025Vmc Machine, 3 4 Axis Vmc Machine, Vmc Center, Vmc Machining, Vmc Machining Center Vmc5025Vmc Machine, 3 4 Axis Vmc Machine, Vmc Center, Vmc Machining, Vmc Machining Center Vmc5025

Contact us

Please feel free to give your inquiry in the form below We will reply you in 24 hours